Light Guide Mould
Light Guide Motorcycle Mould information as below shown :
YoungerMold Factory specializes in light guide mold manufacturing in china.we focuses on the development and research of PC and PMMA transparent products, such as LED light guide mold ,motorbike mould , thick wall lens parts,optic opticals mold ,projector lens mold, etc.
In short, the advantage of light guide strip for automotive/car/motorcycle industry lights is that they can improve the brightness and uniformity of car lights, while reducing energy waste and light pollution.Light guide strips meet different light needs, such as daytime running light, high beam, low beam and turn signal light, molded light guide etc.
Light guide mold should have become an important part of modern car design. As a light guide strip mold manufacturer, we can provide you with satisfactory mold design solutions according to customer requirements.
Automotive Motorcycle Lighting Mould Manufacturer
ZheJiang HuangYan Younger Mould Factory is located in China mold town -Huangyan Taizhou.It is a professional plastic mould .Our factory has been established for twenty years ,founded in 1990s .We design and produce Automotive lighting mould. Our products are widely used in Automotive and motorcycle Industry,Such as : headlamp mould ,taillamp mould,BMC mould ,reflector reflex mould ,light guide mould ,thick wall optics mould ect. Younger Mould Factory with advanced CNC machining centers; EDM machines; wiring, machining, and grinding machines, drilling, and molding machines,and some imported equipment. experienced and professional design teams, rich management experience and a strict quality assurance system, we provide customers with comprehensive and high-quality services. People in our company with integrity and responsibility.
Injection Molding Service for Light Guide Break off sth/Optics Lens Mould /Transparent Parts
Our injection molding machine production service mainly produces car light lenses and light guide strips. We have advanced injection molding machine equipment and a professional technical team, and the quality of the products produced has been highly praised by customers.
Our car light lenses and light guide strips are made of high-quality raw materials, such as optical grade PC, PMMA and high-quality aluminum. The product has good optical properties and physical properties, ensuring the stability and durability of the product, and also has excellent light transmission and high temperature resistance, which can meet customers with different needs.
If you have any production needs about headlight lenses and light guide strips, please feel free to contact us, we will provide you with professional and high-quality services.
Research on injection molding process of car light guide strip mold
Sink marks in the injection molding process of Motorcycle light guide mold are local depressions on the surface of injection molded products caused by volume shrinkage. They are common in places where the thickness of the flesh or wall thickness suddenly changes.
(1) Causes of sink mark formation in light guide mold
Reasons for product structure: unreasonable product design, excessive wall thickness or sudden and uneven wall thickness, resulting in uneven product shrinkage.
Material problems: The shrinkage rate of the material is too large or the flow performance is too poor, as well as insufficient lubricant or wet raw materials, which will cause
Causes depressions and shrinkage marks on the surface of plastic parts.
Influence of mold design: the cross-section of the mold's flow channel and gate is too small, the position of the feed port is unreasonable, and the mold exhaust is poor.
Mold filling resistance is too large, which affects material supply, feeding and cooling. Mold wear causes pressure relief, which will lead to concavity on the surface of the plastic part.
Sinks and shrinkage marks.
Motorcycle light guide mold Injection molding machine reasons: The nozzle hole is too large, which reduces the injection force and makes filling the mold difficult; the check ring, screw or plunger is seriously worn,
Injection pressure cannot be transmitted to the cavity.
Reasons for the molding process: the injection pressure or holding pressure is too low; the injection time is too short or the holding time is too short, the gate is not
During curing, the holding pressure ends; when the temperature is too high during demoulding, the plastic part is not cooled enough, and the temperature at the insert is too low, it will cause the plastic part to
Dimples or orange peel-like slight unevenness appear on the surface.
Improve product design so that the wall thickness of the product should be as uniform as possible; try to use materials with small shrinkage and low viscosity, as needed.
An appropriate amount of lubricant can be added to improve the fluidity of the melt; improve the gate design, appropriately expand the gate and runner cross-section, and
Try to set the location at or near the problem area; improve the design of the mold exhaust system; correctly control the holding pressure and
Holding time to compensate for shrinkage, appropriately extend the cooling time of plastic parts in the mold, and appropriately reduce melt temperature and mold temperature
FAQ
Q: Are you mould factory?
Answer: Yes, Younger mould factory is established in 1999 which specialized in making injection mould.
Q: What kind of mould you can make?
Answer:Head lamp mould ,Tail lamp mould, Thick wall mould ,Light guide mould , optics optical mould ,Fog lamp mould ,reflex reflector mould ,license plate lamp mould ,front turn signal lamp mould ,daytime running lamp mould ,high mount stop lamp mould ,transparent parts production lines ect.
Q: What about your payment terms?
Answer: 50% prepayment in advance, and the balance should be paid before shipment.
Q:Mould T0 trial date ?
Answer:We need calulate the date after customer confirm all drawing . mould making date is not including the drawing design date .
Q: How's annual output of your company?
Answer: We can make 200 sets each year.
Q: How about mould machining report ?
Answer:Our engineer team will send the machining report PPT to client on every Friday .
Q: How long of the mould warranty period?
Answer: The mould warranty period for 1 year(Damage caused by human factors or accident are not within the the scope of warranty), 50% spare parts will send to customer for free.
+86 15267697871
younger8@autolightmould.com
